< Previous | Contents | Next >
PART 3 HULL STRUCTURES
CHAPTER | 1 | GENERAL |
Section | 1 | Definitions |
Section | 2 | General |
Section | 3 | Approval of Plans and Documents |
Section | 4 | Materials |
Section | 5 | Weldings |
Section | 6 | Scantlings |
Section | 7 | Workmanship |
Section | 8 | Corrosion Control |
CHAPTER | 2 | STEMS AND STERN FRAMES |
Section | 1 | Stems |
Section | 2 | Stern Frames |
CHAPTER | 3 | LONGITUDINAL STRENGTH |
Section | 1 | General |
Section | 2 | Bending Strength |
Section | 3 | Shear Strength |
Section | 4 | Buckling Strength |
CHAPTER | 4 | PLATE KEELS AND SHELL PLATINGS |
Section | 1 | General |
Section | 2 | Plate Keels |
Section | 3 | Shell Plating below Strength Deck |
Section | 4 | Special Requirements for Shell Plating |
Section | 5 | Side Plating in way of Superstructure |
Section | 6 | Compensation at ends of Superstructure |
Section | 7 | Local Compensation of Shell Plating |
CHAPTER | 5 | DECKS |
Section | 1 | General |
Section | 2 | Effective Sectional Area of Strength Deck |
Section | 3 | Deck Plating |
8 Introduction to the Classification Technical Rules 2015
Section | 4 | Wood Decks and Deck Compositions |
CHAPTER | 6 | SINGLE BOTTOMS |
Section | 1 | General |
Section | 2 | Centre Keelsons |
Section | 3 | Side Keelsons |
Section | 4 | Floor Plates |
CHAPTER | 7 | DOUBLE BOTTOMS |
Section | 1 | General |
Section | 2 | Centre Girders and Side Girders |
Section | 3 | Solid Floors |
Section | 4 | Bottom Longitudinals |
Section | 5 | Inner Bottom Plating, Margin Plates and Bottom Shell Plating |
Section | 6 | Hold Frame Brackets |
Section | 7 | Open Floors |
Section | 8 | Construction of Strengthened Bottom Forward |
CHAPTER | 8 | FRAMES |
Section | 1 | General |
Section | 2 | Frame Spacing |
Section | 3 | Hold Frames |
Section | 4 | Side Longitudinals |
Section | 5 | Tween Deck Frames |
CHAPTER | 9 | WEB FRAMES AND SIDE STRINGERS |
Section | 1 | General |
Section | 2 | Web Frames |
Section | 3 | Side Stringers |
Section | 4 | Side Transverse |
Section | 5 | Cantilever Beams |
CHAPTER | 10 | BEAMS |
Section | 1 | General |
Section | 2 | Deck Load |
Section | 3 | Longitudinal Beams |
Section | 4 | Transverse Beams |
CHAPTER | 11 | DECK GIRDERS |
Section | 1 | General |
Section | 2 | Longitudinal Deck Girders |
Section | 3 | Transverse Deck Girders |
Section | 4 | Deck Girders in Tanks |
Section | 5 | Hatch Side Girders |
Section | 6 | Hatch End Girders |
CHAPTER | 12 | PILLARS |
Section | 1 | General |
Section | 2 | Scantling of Pillars |
CHAPTER | 13 | ARRANGEMENTS TO RESIST PANTING |
Section | 1 | General |
Section | 2 | Arrangements to Resist Panting forward the Collision Bulkhead |
Section | 3 | Arrangements to Resist Panting abaft Aft-peak Bulkhead |
Section | 4 | Arrangements to Resist Panting between Both Peaks |