Iranian Classification Society Rules

< Previous | Contents | Next >

Guidance for Approval of Manufacturing Process

image

and Type Approval, Etc.


image



 

G C -01-E1. Unless expressly specified otherwise, the requirements in the Guidance apply to ships for which contracts for construction are signed on or after 1 July 2015.CONTENTSSection 1 GeneralSection 2 DefinitionsCHAPTER 2 APPROVAL OF MANUFACTURING PROCESSSection 1 GeneralSection 2-1 Rolled SteelsSection 2-2 Semi Finished Products for Rolled SteelsSection 2-3 Rolled Steels intended for welding with high heat inputSection 2-4 YP47 Steel PlatesSection 3 Steel Tubes and PipesSection 4 Castings and Steel ForgingsSection 5 Crankshafts under special requirementsSection 6 Aluminium AlloysSection 7-1 Copper Alloy CastingsSection 7-2 Copper and Copper Alloy TubesSection 8 Special Cast Iron ValvesSection 9 AnchorsSection 10-1 Marine ChainsSection 10-2 Marine Chain AccessoriesSection 10-3 Offshore Chains and Chain AccessoriesSection 11 Wire RopeSection 12 Synthetic Fibre RopesSection 13 FRP ShipsSection 14 Boiler and Pressure VesselCHAPTER 3 TYPE APPROVALSection 1 GeneralSection 2 Welding MaterialsSection 3-1 Anti-corrosive PaintsSection 3-2 Non-slip PaintsSection 4 Acid Resisting PaintsSection 5 Loading InstrumentsSection 6 High Holding Power Anchors and Super High Holding Power AnchorsSection 7-1 Emergency Towing ArrangementsSection 7-2 Equipment for mooring at SPMSection 8-1 Diesel Engines 1Section 8-2 Diesel Engines 2(Mass Produced Diesel Engines)Section 9 Crankcase Explosion Relief valvesSection 10 Crankcase Oil Mist Detection ArrangementsSection 11 Exhaust Gas TurbochargersSection 12 Hydraulic Motors and Hydraulic PumpsSection 13 Air CompressorsSection 14 Safety ValvesSection 15 Machinery and Equipment for ShipsSection 16 Plastic PipesSection 17 Flexible Hose Assembly(3) Test items, test method and criteriaSection 18 Mechanical JointsSection 19 Air Pipe Automatic Closing DevicesSection 20 Level IndicatorsSection 21 Electrical Equipment and CablesSection 22 Cable LayingSection 23 Automatic and Remote Control SystemsSection 24 Equipment related to Ventilation Systems in Oil TankersSection 25 Securing DevicesSection 26 Fire Protection MaterialsSection 27 Materials for Refrigerated Chambers and Oil-impervious CompositionSection 28 Materials of Reinforced PlasticsSection 29 Water Level Detection and Alarm SystemSection 30 Protective Coating Systems for Ballast TanksSection 31 LED lighting fittingsSection 32 Corrosion Resistant Steels2. Corrosion Resistant Steel is to be graded and approved its manufacturing process in accord- ance with Ch 2, Sec 2-1 of this Guidance.(5) The welding processes and the brand name of the welding consumables to be used for approval. : 3 copies(C) Specimens are to be weighed to an accuracy of ±1 mg.(a) Sampling of test specimens, magnification of photomicrograph and evaluation of dis- continuous surface to be in accordance with requirements in 3205. 3..Section 33 Protective Coating Systems for Cargo Oil TanksSection 34 Fiber Reinforced Plastic GratingsCHAPTER 4 DESIGN APPROVALSection 1 GeneralSection 2 Loading Instrument ProgramSection 3 Container Lashing calculation programCHAPTER 5 APPROVAL OF QUALITY ASSURANCE SYSTEMSection 1 GeneralSection 2 AssessmentSection 3 ApprovalSection 4 Requirements of Quality Assurance System (KS Q ISO 9001:2009 / ISO 9001:2008)CHAPTER 6 MANUFACTURER APPROVALSection 1 GeneralSection 2 AssessmentSection 3 Approval<1. Approval Certificate for Manufacturing Process><2. Type Approval Certificate><3. Design Approval Certificate><4. Approval Certificate for Quality Assurance System><5. Approval Certificate for Manufacturer><6. Application Form for Approval>GUIDANCE FOR APPROVAL OF MANUFACTURING PROCESS AND TYPEICS